MANEK - automotive service station and garage equipment hydraulic hoist, car washer

Vehicle Washers	Pneumatic Grease Pump	Portable Service Unit
Automatic Tyre Changers	Hydraulic Hoist	Mechanical 2 Post Lifts
	Reciprocating Air Compressor

Link to Automotive Engine Rebuilding Machines like Crankshaft Regrinders, Line Boring Machines, Cylinder Boring and Honing Machines, Con Rod Boring, Grinding & Honing Machines, Surface Grinders, Valve Grinders, etc.

Reciprocating Pumps (Vehicle Washers)

Model:	ATW 03
Discharge (lpm):	25
Displacement (lpm):	26
No. of Guns:	2
No. of Plungers:	1
Operating Pressure (kgf/cm2):	25
Motor HP / RPM:	3 / 1440
Pump Speed (RPM):	360

Standard Accessories: Electric Motor, Starter, Belts, Hoses and Guns.
Optional Accessories: 300 Litres Tank. (Note: tank shown in the photograph is an optional accessory)

Pneumatic Grease Pump

Model:	ATG 50
Pressure Ratio:	50 : 1
Output at 8 Kg/cm2 Air Pressure (Gms.):	320 - 390
Working Pressure Range of Air (Kg/cm2):	4 - 10
Recommended Working Pressure of Air (Kg/cm2):	8
Normal Blocked Pressure at 8 Kg/cm2 Air Pressure (Kg/cm2):	400
Air Equipment (FAD) (lpm):	310
Delivery Hose Length x ID (mm):	2200 x 6
Drum Capacity (kgs.):	50
Gun:	Trigger Type
Net Weight (Kgs.):	36

Standard Accessories: 2200 mm Wire Braided Hose and Trigger Type Gun

Pneumatic Grease Pump

Portable Service Unit

Practically a small service station on wheels, this is a multi purpose portable unit that could be used for greasing, painting, tyre pressure checking and air filling.

1 HP Direct Mounted Reciprocating Air Compressor at a maximum working pressure of 8 Kg/cm2, mounted on a 45 litres horizontal air receiver
Pneumatic Grease Pump of 50:1 ratio, mounted on a grease drum of 25 Kg
Tyre Inflator at a maximum pressure of 10 Kg/cm2 (140 PSI)

Standard Accessories: Electric Motor, Starter, Belts.

Automatic Tyre Changers

- Turn Table with four self centering jaws for easy clamping of wheel discs from inside or outside
- High powered double acting pneumatic cylinder to hold the rim rigidly to execute the mounting & demounting of tyres
- Air powered single acting cylinder operated bead breaker system

Wheel Rim Size:	10" - 18" (Outer) / 12" - 20" (Inner)
Rim Width	3" - 12"
Bead Braking Range	70 - 325 mm
Bead Braking Force	2150 kgs.
Compressed Air Supply	8 - 15 bar
Operating Pressure	6 - 8 bar
Electric Motor	1 HP
Net / Gross Weight	220 / 365 kgs.
Case Dimensions	105 x 92 x 100 cms & 102 x 74 x 38 cms
Shipping Volume	1.3 m3

Standard Accessories: Motor, Tyre inflator, Tyre lever, Valve pin remover and die

Model: TC-XL-10

Model: TC-XL-20

- Wheel Centering by Taper Cones and Wheel Clamping by a Quick Mounting and Clamping System
- Eliminates pneumatic cylinder for Clamping
- Air powered single acting cylinder operates the bead breaker system
- Fitted with Lubricator Unit

Wheel Rim Size	10" - 20"
Rim Width	3" - 10"
Bead Braking Range	70 - 325 mm
Bead Braking Force	2150 kgs.
Compressed Air Supply	8 - 10 bar
Operating Pressure	6 - 8 bar
Electric Motor	1 HP
Net / Gross Weight	220 / 365 kgs.
Case Dimensions	105 x 92 x 100 cms & 102 x 74 x 38 cms
Shipping Volume	1.3 m3

Standard Accessories: Motor, Tyre lever, Valve pin remover & die, Quick Change Lock Nut assly, Taper Cones, Locating pins, Drive Plate

- No Air Compressor Required
- Clamping of wheels using centre hole. Eliminates uneven rotation
- Bead braking using eccentric mechanism. Uniform Bead Braking force and no damage to beads

Rim Diameter (max)	21"
Rim Width	3" - 10"
Rim Centre Hole Range	2" - 4.25"
Net / Gross Weight	170 / 290 kgs.
Case Dimensions	110 x 70 x 80 cms & 102 x 74 x 38 cms
Shipping Volume	1.0 m3

Standard Accessories: Motor, Tyre lever, Valve pin remover & die, Quick Change Lock Nut assly, Taper Cones, Locating pins, Drive Plate

Model: TC-XL-30

Hydraulic Hoist

- Hydraulically operated with oil pressurized by compressed air
- Plungers are made of high grade steel, ground to close tolerance and hard chrome plated, for high wear resistance and good surface finish
- Available in Single and Twin Post

Model:	ATU 4	2 ATU 8
Type:	Single Post	Twin Post
Capacity (Tons):	4	8
Operating Pressure (Kg/cm2):	8 to 12	8 to 12
Lifting Height (mm):	1500	1500
Overall Length Front/Rear (mm):	4500 / --	4500 / 1500
Ramp Width (mm):	700	700
Oil Fill Capacity (litres):	180 - 190	360 - 380

Standard Accessories: Ramp with Sliding Supports, Oil Receiver tank and Control Valves

Mechanical 2 Post Lifts

- The driving post column motor drives the other post simultaneously with a high quality closed ring chain present in the base frame, with all its links riveted for maximum safety.
- Chain guides of rubber to reduce vibration and provide noiseless chain drive
- For Safety the equipment is fitted with top and bottom post limit switches, chain brake cut-off system and mechanically interlocked contactors
- Electric Shock Proof System
- Automatic Arms Locking and Release Device

Model	2.5 T	3.2 T
Capacity (kgs.)	2500	3200
Lifting Time (seconds)	50	50
Max lifting height (mm)	1930	1930
Electric Motor (HP)	2.0	3.0
Net / Gross Weight (kgs.)	550 / 650	600 / 700
Overall Dimensions (m)	2.7 x 0.7 x 0.7 & 3.2 x 1.4 x 0.1	2.7 x 0.7 x 0.7 & 3.2 x 1.4 x 0.1
Shipping Volume (m3)	1.8	1.8

Note: Also available in capacity of 2750 Kgs.

Reciprocating Air Compressor

Model:	ATT 1000
Type:	Two Stage
Displacement (CFM) / (Ltr./Min.):	35 / 1000
Working Pressure (Kg/cm2) / (PSI):	12 / 170
Motor HP:	10
Tank (Litres):	420

Standard Accessories: Motor, Starter, ‘V’ Belts.

Maneklal Global Exports
67 Bajaj Bhavan, Nariman Point, Mumbai - 400021, INDIA
Tel: +9122-22041340 / 41 / 42. Fax: +9122-22041389
WhatsApp: +918879795490
e-mail: sales@maneklalexports.com / maneklalexports@gmail.com / Enquiry Form